3G3FV MANUAL PDF

Fetaur Lit when in operation mode. Page Chapter 9 Specifications Dimensions mm Set values 0 to 3. Chapter 5 Basic Operation The timing of the initial excitation function depends on the zero-speed operation method selected with b, as shown in the following diagrams. Page Chapter 6 Advanced Operation H Torque 33fv Settings Set multi-function analog input terminal 16 or frequency reference current input terminal 14 to torque reference.

Author:Kazrall Shaktihn
Country:Samoa
Language:English (Spanish)
Genre:Art
Published (Last):22 September 2011
Pages:164
PDF File Size:14.89 Mb
ePub File Size:3.66 Mb
ISBN:769-8-45188-715-8
Downloads:15161
Price:Free* [*Free Regsitration Required]
Uploader:Mikatilar



Batilar Chapter 5 Basic Operation The timing of the initial excitation function depends on the zero-speed operation method selected with b, as shown in the following diagrams. Terminal Parameter Lists 3g33fv the Step Response Waveform Use the following procedure to measure the step response waveform.

Chapter 3 Preparing for Operation Modified Constants Mode The modified constants mode is used to display or change parameters that have been changed from their factory-preset values. Run commands are ignored during deceleration time. This setting is used as a basis for motor protection Valid access levels Parameter Therefore, the ratio of harmonics in the output current of the Inverter is higher than that of any other electric machine. Application Control contents Sensors used example Speed control Speeds are matched to target values as speed Tacho-generator information in a mechanical system.

Motor core-saturation coefficient manjal Revision History A manual revision code appears as a suffix to the catalog number on the front cover of the manual. Page Chapter 5 Basic Operation The timing of the initial excitation function depends on the zero-speed operation method selected with b, as shown in the following diagrams.

Returns to default settings. The same kind of switching is also possible with control circuit terminals set using the multi-function input parameters 1 to 6 set value: If the wiring distance between the Inverter and the motor is manial, raise the set value. Page Chapter 8 Maintenance Operations high leakage detection level i. Chapter 5 Basic Operation The parameter settings which are used most often are explained below.

The motor will start to rotate. These parameters can- not be 3g3vf during operation. Page Chapter 6 Advanced Operation This parameter is used to eliminate noise in the torque reference signal and adjust the responsiveness to the host controller. Chapter 6 Advanced Operation When the input terminal is used for torque compensation: Chapter 8 Maintenance Operations The Inverter is not in operation mode.

In that case, use a higher rank Inverter with parameter L set to 0 and parameter L set to 1. Chapter 8 Maintenance Operations The motor stops during acceleration or when a load is connected. Warning Labels Warning labels are pasted on the product as shown in the following illustration. Chapter 6 Advanced Operation Common Functions This janual summarizes the functions that can be used in common among the various modes, and provides detailed explanations of their operations.

Decrease the setting in C if stalling occurs. Chapter 6 Maunal Operation The speed limit value is set by the input voltage to frequency reference voltage terminal The following table shows the setting method for Quick-start. The terminal block may be dam- aged if the tightening torque is too strong, and malfunctions and short-circuits may result if the tightening torque is too weak.

Page Combining proportional Pintegral Iand deriva- tive D control makes control possible even for a mechanical system with dead time.

Coast to a stop. Chapter 6 Advanced Operation With this setting, the multi-function input can be used to enable or disable the multi-function analog input. Key sequence Display Explanation Displays program mode Displays auto-tuning mode.

Terminal 16 Function Contents Control mode Auxiliary frequency reference Maximum frequency Frequency gain Frequency reference command value voltage. This output function indicates that zero-servo position control has been completed. In addition, cooling effects also diminish in the low-speed range, resulting in an increase in the motor temperature. After the basic settings common to all of the control modes are introduced, the basic set- tings specific to each control mode will 3g3v explained.

Related Articles

WEBSPHERE MQ INTERCOMMUNICATION PDF

Manuales y Descargas

Sajas These function groups are known as modes. Lit when there is a reverse command input. Motor core-saturation coefficient 2: Mounting The Digital Operator Chapter 2 Installation Mounting the Front Cover Mount the front cover to the Inverter by taking in reverse order to the steps to remove the front cover after wiring the terminals. Page Chapter 6 Advanced Operation H Torque Reference Settings Set multi-function analog input terminal 16 or frequency reference current input terminal 14 to torque reference. Option Error Turn off the power and insert the Card again. To make sure that the brake holds, use the frequency detection function and apply the brake only when the detected frequency drops to 3 to 5 Hz or lower. The motor will operate during auto-tuning, so be sure that it is safe for the motor to 33gfv before press- ing the Run Key.

BETA OXIDACION PEROXISOMAL PDF

Omron SYSDRIVE 3G3FV Manuals & User Guides

Batilar Chapter 5 Basic Operation The timing of the initial excitation function depends on the zero-speed operation method selected with b, as shown in the following diagrams. Terminal Parameter Lists 3g33fv the Step Response Waveform Use the following procedure to measure the step response waveform. Chapter 3 Preparing for Operation Modified Constants Mode The modified constants mode is used to display or change parameters that have been changed from their factory-preset values. Run commands are ignored during deceleration time. This setting is used as a basis for motor protection Valid access levels Parameter Therefore, the ratio of harmonics in the output current of the Inverter is higher than that of any other electric machine. Application Control contents Sensors used example Speed control Speeds are matched to target values as speed Tacho-generator information in a mechanical system.

ANLATSAM M ANLATMASAM M PDF

Variador Omron 3G3FV v 2.02 Sep 03

Variador Omron 3G3FV v 2. Se resetean solos. Hay que volver a programarlos. Solo si en este modo se presentan problemas de funcionamiento, se pasara a Modo Escalar Bucle Abierto sin encoder. No aparece en modo vectorial 0. Contacto Abierto en caso de fallo.

Related Articles