A650E TRANSMISSION PDF

The five-speed was somewhat overshadowed by the more popular six-speed automatics and often sparked complaints from Lexus buyers, who could only order their cars with the AE and not a five-speed manual. Yet the A provided smooth shifting and helped increase fuel efficiency. Background The AE was a five-speed electronic control transmission that was virtually identical to its hydraulic automatic transmission siblings, but used an electronic control unit, electronic sensors and numerous electronic parts to shift gears. The sensors then sent the information to the electronic control unit, which in turn operated the clutch, shift points and torque converter lock-up.

Author:Tuk Kazisar
Country:Tunisia
Language:English (Spanish)
Genre:Health and Food
Published (Last):28 May 2012
Pages:28
PDF File Size:12.24 Mb
ePub File Size:12.66 Mb
ISBN:341-6-33807-904-8
Downloads:14423
Price:Free* [*Free Regsitration Required]
Uploader:Necage



Cody Graham Leave a comment One of the most common misconceptions about the IS and other cars that share the 5 speed Lexus automatic is its ability to handle some real power. In this article, I will outline what it takes to make it handle some power on the cheap, mods that almost anyone can do. Everyones mileage will vary, no doubt, and part of its longevity rests with you, the driver, but this will be the best thing you can do without spending a ton of money.

There are a few theories on how to make automatic transmissions last. I knew, going in, that my stock transmission might not last too long, so I was prepared to do some experimenting. What I have ended up with is a transmission that was amazing at a whp level over ft lb of torque also , and today, is still holding up to whp, once in 3rd gear and above. I have not modified the valve body in any way and the transmissions guts have never been removed. The transmission pan and valve body will need to be removed, but that is it really.

How, you say? Well, I did a bunch of research and found that it is a delicate balancing act to make these transmissions work right with some real power behind them.

The first problem I ran into was hitting the rev limiter under power. Stock rev limiter is around and the transmission starts its shift around There are two ways around this — raise the rev limiter or make it shift faster. The best way without a full transmission build, and even without a valve body replacement is to modify the accumulators. Accumulators are the small piston like devices that allow fluid to accumulate, in order to dampen shifts.

The springs need to be stiffer to make the shifts firmer, but they still need to be in place to maintain a little bit of shift damping. There is no need to be chirping tires for a quarter throttle shift. I was never able to find good information on stock spring rate, or even find a good source for stiffer springs that would fit properly. Instead, I simply shortened the space the spring could travel. Unfortunately, I do not have measurements, as I simply did not take them when I was performing this mod 3 years ago.

Some day, I will pull her apart and get exact measurements. To shorten the travel, I simply made bushings for the springs. Anything metal that fits inside the accumulator will work. I shimmed all 4 of mine approximately 15 mm. That was attempt 2. There are small holes inside the accumulators that you do not want to block, but the a design prevents that to an extent. One more quick mod related to this is to simply turn line pressure up. On the side of the valve body, there is a pressure control — simply use a straight edge screwdriver to push in and rotate to the next detent.

Even with the above listed modifications, getting the trans to shift too quickly will not be good. At the power levels required for these types of modifications, hopefully you are running some sort of standalone already.

The 2jz is very capable of spinning higher than the stock rpm redline. One other thing I do is retard timing during the shift. This reduces power just slightly low timing keeps the turbo spooled though until the lower RPM after the shift point is realized and the timing is obviously much higher there. It is my opinion that these rods that people do are not good for transmission longevity at all. The fact is, they make the transmission slam into gear pretty much every single shift.

This is not good on the internal components of the transmission. Things like this are what causes the infamous sprag gears to roll over. An instantaneous hit of power is much harder on the sprag than applying the power smoothly. Drop a hammer on a piece of glass versus lay a hammer on a piece of glass. Use the transmission selector buttons to maintain the gear you want.

Prevent the transmission from downshifting if at all possible under full throttle. If the engine is below RPM, applying full throttle will invoke a downshift, no matter what gear you have selected. There is one way around this — the snow button. Post navigation.

GENGIVITE ULCERATIVA NECROSANTE PDF

Making the A650e transmission survive on the cheap. Part 2

.

JIS C 0704 PDF

Toyota A transmission

.

CADENCE CONFORMAL LEC USER GUIDE PDF

Transmission repair manuals A650E

.

Related Articles