I have airplanes I like to fly just above idle. Prior approval of the mannual government authorities may be required. When the flight conditions are set, the trim operation can be coupled with among all the conditions which fuatba mode is selected. Functions and mixing functions necessary for each model type are set in advance at the factory.

Author:Voodoogrel Mezir
Language:English (Spanish)
Published (Last):25 January 2005
PDF File Size:1.19 Mb
ePub File Size:11.31 Mb
Price:Free* [*Free Regsitration Required]

Mauzragore Curves may be linear or exponential, or point-based up to 17 points. A typical menu screen is shown selection, frequency setting, end point setting, and below.

Select the switch A and B. These have a ratchet action and a centre detent, though the centre positions were barely detectable on the review unit. The Linkage menus are where you mmanual all the basic setting fjtaba, including creating new models, frequency selection, control assignments, and servo adjustments. The hovering pitch can be Setting method conditions. I know how it flies and will be able to feel the transmitter pretty well flying this airplane.

I really have no clue about this, but it seems to me if cell phones at a dime a dozen can have pleasing color screens the technology is available at a price which could be implemented on these transmitters. This function can smooth things out a bit. Multiple servos can be linked to the same function, thus avoiding the need for Y-leads in the model. The new protocol supports channels, step resolution and channel grouping. Screen Common operations used in function setup screen This section describes the functions often used at the function setup screen.

Capacity is mAh, and based on the published current consumption of mA the maximum safe duration should be around 2. Use the Normal must be done by a Futaba service center. Flight conditions are superbly flexible on the Futaba 12FG. Normally, it is used with high side and low side trim function.

There is also a separate battery fail safe. The sub-trim menu allows you to fine tune the neutral position so 12fgn control surfaces are precisely where they need to be for flight.

Futaba RSB S. The servos operate smoothly at a fixed speed corresponding to the set speed. Terms of Use Privacy Policy. Page 42 Receiver and servo connection Connect the receiver and servos in accordance with the connection diagram shown below.

Inevitably the model had to be re-trimmed, mixer and diff adjusted, in fact it was like starting with a brand new model, let alone a new radio! Stick Adjustment Adjustment of Throttle Stick Ratchet System You can also choose either airplane ratchet Adjustment of the stick lever length system or helicopter-touch.

Futaba has come a long way in the programming and menu design since my 8U, but they still have a way to go with the display itself. For example, most have an AFR page for setting the curves. Page 93 BUTTERFLY This function allows powerful brake operation by simultaneously raising the left and right ailerons and lowering the flaps camber flap, This setting will allow the ailerons to be raised while the flaps are simultaneously lowered.

Styling Ease of Use Options. Have regular maintenance performed. The electronics are mainly confined to a futxba motherboard that is dominated by a huge pin custom chip. The Model Select function of the manual. Depending on how you install the servos, it may be necessary to reverse the travel direction so the transmitter sticks operate them properly. Looking at the menu categories in more detail: The size of each increment is adjustable and their positions are displayed on the LCD.

When the aileron stick is manipulated, the aileron and brake flaps perform the aileron operation simultaneously and the operation characteristic of the roll axis is improved. I then programmed the same switch to deactivate the snapflap and crow mixers according to the flight condition. Table of Contents Add to my manuals Add.

You can however change those presets if it makes sense to do so. The 12FG makes having multiple models at the field very 12ggh and the feature list it brings to airplanes, gliders and helicopters is extremely comprehensive. Page 43 Servo connection by model type The T12FG transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu.

When using this function, always check initial operation with the propeller removed. Most 10 Related.


Futaba 10CAG Manuals

Yet they all have one thing in common — they all need advanced radios to control them. I needed little persuasion to review this radio. Out of the Box I have to admit to turning into a kid in a toyshop when the man from Parcel Force arrived, and the package was soon spilling its contents. These included a smart looking transmitter, R receiver, mains charger and user manual. Also included were a couple of Allen keys, and a bright orange neck strap. No servos are provided with the 12FG.


FUTABA 12FG Manuals & User Guides

It means you can adjust exactly how you want the servo to react at various stick positions. Idle down setting The Condition Select function automatically allocates The idling speed can be lowered with one touch by 12fgy the default condition and is the only fhtaba active when a a switch without changing the throttle trim position. Nestling in the side cheeks are a couple of rotary levers. Page 93 BUTTERFLY This function allows powerful brake operation by simultaneously raising the left and right ailerons and lowering the flaps camber flap, This setting will allow the ailerons to be raised while the 1fgh are simultaneously lowered. Space is also counted as 1 character. A needle curve can be set. The aerial is just over a meter in length futabw screws into a smart chromed ball-joint.


FUTABA manuals

Felabar AFR AFR Function is used to adjust the throw and operation curve of the stick, lever, and switch functions for each flight condition of which there are 8. Always read [Precautions when mounting the receiver and servos] or [Before using]. Scrolling through the menus is intuitive and once I learned where to find the information, setting up manula parameters of a model is very simple. Mixing applied in other swash modes is different, but the setting procedure is the same.

Related Articles